Product Description

1.Feature and advantage:

Theme Park  Mini Track Train/ Locomotive with 120 Seats  

Manufacturer for Amusement Rides Mini Diesel  Track Train with High quality & conpetitive price you. Customer is welcome to visit our new showroom and factory located in HangZhou City, China. 

2.Specifications

TY02-7C-120W Transparent-type Sightseeing Mini Train

Gauge: 762/900/1435mm
Marshalling:  locomotive +coal water truck  + carriage*3
Speed: 10km/h
Crew: 40 *3=120
Mat limit slope: 30 per thousand
Restriction curve radius: 30m 
Power: diesel generating set (Cummins) 

2.1 Ambient conditions and vehicle parameters

1) Project location height is not more than 2000 meters above sea level.
2) The air temperature is between -10 and 40 degree.
3) Electronic components must not be activated without dehumidification in relative humidity greater than 95% or condensation.
4) Vehicles should be CZPT to withstand the invasion of wind and sand and the resistance to salt spray
5) Line gauge: 762mm
6) Limiting slope: 30 ‰ (reduction calculations for curves)
7) The radius of the line longitudinal curve is 200m
8) Line minimum curve radius 40m, difficult area 30m
   

              
2.2 Vehicle parameters

1) Grouping: locomotive + coal water truck + passenger car + passenger car + passenger car
2) Overall dimensions: The whole group: 41m (length) x 2.4m (width) x 3.2m (height);
3) Speed: 0-10km/h, large curve, speed uphill 8km/h.
4) Crew: 40*3=120 seats
5) Emergency braking distance: <15m at the highest speed
6) Frame anti-corrosion treatment: zinc-rich primer dual + dual top coat .
7) Power Source: CZPT Diesel Generator 80kw
8) Drive power: 11kw*4
9) Air whistle, continuous cold steam effect
10) Tour Xihu (West Lake) Dis. Voice Interpretation System
11) Steel frame anti-corrosion treatment: epoxy zinc-rich primer + middle coating + top coat 2 degrees  Drive motor: Three-phase variable-frequency motor 11KW*4
12) Power Source: CZPT Diesel Generator 80kw (HangZhou Int.)
13) Speed Control Mode: V-F Frequency Control
14) Voltage: control voltage, lighting voltage: 24V (safety voltage), power voltage AC 380v
15) Braking: Working brake: dynamic braking, DC braking ; Emergency braking: Electropneumatically combined braking (failure of wind braking).
16) Driver seat : Sitting position 2 seats
17) Air compressor: three-phase air compressor (HangZhou)
18) Inverter plc: Delta (ZheJiang )
19) Coach:9.5m*2.4m*3.3m
20) The welding and spraying zinc of the frame:Q235 profile.
21) The roof:FRP shell with solid wood buckle
22) External walls: steel, solid wood (Hong Xuesong) wood oil 8 degrees.
23) Bogie form: calculating the axle weight of 2.5 tons
24) Floor: bamboo flooring overlay vehicle and ship floor leather (pineapple solid wood flooring / other charges)
25) Sitting stool: 40 solid wood
26) Small table board:10 train style (grain effect)
27) Window:14 oak solid wood windows
28) Door :2 oak solid wood
29) Air conditioning: single refrigeration top 3 sets
30) Heating in winter: electric heating 500W x 6
31) Sound 

2.3 Company profile

HangZhou dising technologies Co., Ltd.is located in the east lake new technology development zone in HangZhou, ZheJiang province.It is a professional supplier of tourist attraction, theme park, characteristic town, and commercial block slow rail transit system;Our service covers the whole process of slow rail transit system survey and design, special track vehicle design and so on.
We promise to improve our professional skills and be based on a careful design attitude, a profound understanding of customer needs and a rich experience in project implementation, to provide customers with high quality and reliable products and economic and reasonable projects.

2.4 Products Series

In the years of industry experience, the company created the ZheJiang tenyun steam locomotive replica plate, the Tianya  corner scenic spot in ZheJiang , the HangZhou Yuet square project, the tram, the ZheJiang lling National Agricultural Park sightseeing train, the Xihu (West Lake) Dis. Lu Jia Village sightseeing small train and so on. The main products covers 3 kinds of landscapes:tourism. Sightseeing trains, sightseeing trams and locomotives 3 kinds of landscapes.

1. Electric Train Sets
2. Electric Locomotive
3. Fun Train
4. Sightseeing Mini Train
5. Tram

2.5 Delivery and Shipment

Shipping by sea: Around 4 weeks to arrive.
Delivery Time: Around 30 working days after receipt of deposit.
MOQ: 1 set.
Payment Term:  30% T/T deposit, 70% T/T before delivery.

2.6 Warranty and post service 

Mini Electric Trackless Train for Tourist: 1 year full warranty,offer FREE components under EXW shipped term.
oversea engineer aftre sale service available

2.7 FAQ

Q1. What is your terms of packing?

A: Generally, we pack our goods in neutral white boxes and brown cartons. If you have legally registered patent, we can pack the goods in your branded boxes after getting your authorization letters.

Q2. What is your terms of payment?

A: T/T 30% as deposit, and 70% before delivery. We’ll show you the photos of the products and packages before you pay the balance.

Q3. What is your terms of delivery?

A: EXW, FOB, CFR, CIF, DDU.

Q4. How about your delivery time?

A: Generally, it will take 30 to 60 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.

Q5. Can you produce according to the samples?

A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.

Q6. What is your sample policy?

A: We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and the courier cost.

Q7. Do you test all your goods before delivery?

A: Yes, we have 100% test before delivery

Q8: How do you make our business long-term and good relationship?

A:1. We keep good quality and competitive price to ensure our customers benefit ;

2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.

Screw Sizes and Their Uses

Screws have different sizes and features. This article will discuss screw sizes and their uses. There are 2 main types: right-handed and left-handed screw shafts. Each screw features a point that drills into the object. Flat tipped screws, on the other hand, need a pre-drilled hole. These screw sizes are determined by the major and minor diameters. To determine which size of screw you need, measure the diameter of the hole and the screw bolt’s thread depth.

The major diameter of a screw shaft

The major diameter of a screw shaft is the distance from the outer edge of the thread on 1 side to the tip of the other. The minor diameter is the inner smooth part of the screw shaft. The major diameter of a screw is typically between 2 and 16 inches. A screw with a pointy tip has a smaller major diameter than 1 without. In addition, a screw with a larger major diameter will have a wider head and drive.
The thread of a screw is usually characterized by its pitch and angle of engagement. The pitch is the angle formed by the helix of a thread, while the crest forms the surface of the thread corresponding to the major diameter of the screw. The pitch angle is the angle between the gear axis and the pitch surface. Screws without self-locking threads have multiple starts, or helical threads.
The pitch is a crucial component of a screw’s threading system. Pitch is the distance from a given thread point to the corresponding point of the next thread on the same shaft. The pitch line is 1 element of pitch diameter. The pitch line, or lead, is a crucial dimension for the thread of a screw, as it controls the amount of thread that will advance during a single turn.

The pitch diameter of a screw shaft

When choosing the appropriate screw, it is important to know its pitch diameter and pitch line. The pitch line designates the distance between adjacent thread sides. The pitch diameter is also known as the mean area of the screw shaft. Both of these dimensions are important when choosing the correct screw. A screw with a pitch of 1/8 will have a mechanical advantage of 6.3. For more information, consult an application engineer at Roton.
The pitch diameter of a screw shaft is measured as the distance between the crest and the root of the thread. Threads that are too long or too short will not fit together in an assembly. To measure pitch, use a measuring tool with a metric scale. If the pitch is too small, it will cause the screw to loosen or get stuck. Increasing the pitch will prevent this problem. As a result, screw diameter is critical.
The pitch diameter of a screw shaft is measured from the crest of 1 thread to the corresponding point on the next thread. Measurement is made from 1 thread to another, which is then measured using the pitch. Alternatively, the pitch diameter can be approximated by averaging the major and minor diameters. In most cases, the pitch diameter of a screw shaft is equal to the difference between the two.

The thread depth of a screw shaft

Often referred to as the major diameter, the thread depth is the outermost diameter of the screw. To measure the thread depth of a screw, use a steel rule, micrometer, or caliper. In general, the first number in the thread designation indicates the major diameter of the thread. If a section of the screw is worn, the thread depth will be smaller, and vice versa. Therefore, it is good practice to measure the section of the screw that receives the least amount of use.
In screw manufacturing, the thread depth is measured from the crest of the screw to the root. The pitch diameter is halfway between the major and minor diameters. The lead diameter represents the amount of linear distance traveled in 1 revolution. As the lead increases, the load capacity decreases. This measurement is primarily used in the construction of screws. However, it should not be used for precision machines. The thread depth of a screw shaft is essential for achieving accurate screw installation.
To measure the thread depth of a screw shaft, the manufacturer must first determine how much material the thread is exposed to. If the thread is exposed to side loads, it can cause the nut to wedge. Because the nut will be side loaded, its thread flanks will contact the nut. The less clearance between the nut and the screw, the lower the clearance between the nut and the screw. However, if the thread is centralized, there is no risk of the nut wedgeing.

The lead of a screw shaft

Pitch and lead are 2 measurements of a screw’s linear distance per turn. They’re often used interchangeably, but their definitions are not the same. The difference between them lies in the axial distance between adjacent threads. For single-start screws, the pitch is equal to the lead, while the lead of a multi-start screw is greater than the pitch. This difference is often referred to as backlash.
There are 2 ways to calculate the pitch and lead of a screw. For single-start screws, the lead and pitch are equal. Multiple-start screws, on the other hand, have multiple starts. The pitch of a multiple-start screw is the same as its lead, but with 2 or more threads running the length of the screw shaft. A square-thread screw is a better choice in applications requiring high load-bearing capacity and minimal friction losses.
The PV curve defines the safe operating limits of lead screw assemblies. It describes the inverse relationship between contact surface pressure and sliding velocity. As the load increases, the lead screw assembly must slow down in order to prevent irreversible damage from frictional heat. Furthermore, a lead screw assembly with a polymer nut must reduce rpm as the load increases. The more speed, the lower the load capacity. But, the PV factor must be below the maximum allowed value of the material used to make the screw shaft.

The thread angle of a screw shaft

The angle between the axes of a thread and the helix of a thread is called the thread angle. A unified thread has a 60-degree angle in all directions. Screws can have either a tapped hole or a captive screw. The screw pitch is measured in millimeters (mm) and is usually equal to the screw major diameter. In most cases, the thread angle will be equal to 60-degrees.
Screws with different angles have various degrees of thread. Originally, this was a problem because of the inconsistency in the threading. However, Sellers’s thread was easier to manufacture and was soon adopted as a standard throughout the United States. The United States government began to adopt this thread standard in the mid-1800s, and several influential corporations in the railroad industry endorsed it. The resulting standard is called the United States Standard thread, and it became part of the ASA’s Vol. 1 publication.
There are 2 types of screw threads: coarse and fine. The latter is easier to tighten and achieves tension at lower torques. On the other hand, the coarse thread is deeper than the fine one, making it easier to apply torque to the screw. The thread angle of a screw shaft will vary from bolt to bolt, but they will both fit in the same screw. This makes it easier to select the correct screw.

The tapped hole (or nut) into which the screw fits

A screw can be re-threaded without having to replace it altogether. The process is different than that of a standard bolt, because it requires threading and tapping. The size of a screw is typically specified by its major and minor diameters, which is the inside distance between threads. The thread pitch, which is the distance between each thread, is also specified. Thread pitch is often expressed in threads per inch.
Screws and bolts have different thread pitches. A coarse thread has fewer threads per inch and a longer distance between threads. It is therefore larger in diameter and longer than the material it is screwed into. A coarse thread is often designated with an “A” or “B” letter. The latter is generally used in smaller-scale metalworking applications. The class of threading is called a “threaded hole” and is designated by a letter.
A tapped hole is often a complication. There is a wide range of variations between the sizes of threaded holes and nut threads, so the tapped hole is a critical dimension in many applications. However, even if you choose a threaded screw that meets the requisite tolerance, there may be a mismatch in the thread pitch. This can prevent the screw from freely rotating.